Expert Answers about Chevrolet Hitch Aligners
- How Wide Is The etrailer Hitch Pin Alignment Collar e98942?
- I had our warehouse measure the etrailer Hitch Pin Alignment Collar for Bike Racks, Cargo Carriers, and Tow Bars - 2" Hitches # e98942 you were looking at and it is 1-3/16" wide as shown in the included diagram.
As long as you have 1-3/16" clearance between the receiver and the end of the 2" accessory you are using this would be a great fit for you.
I included a video of the # e98942 for you to take a look at.
view full answer... - Draw-Tite Hitch Ground Clearance on 2018 Subaru Forester
- The height of the Draw-Tite Hitch # 75876 from the bottom of the receiver to the top of the mounting brackets is 10-11/16 inches. I attached a picture I made below to illustrate where it is measured. Ground clearance can vary from car to car due to suspension wear and other factors, so I hope this measurement helps you find the exact clearance for your own specific vehicle.
Along with your hitch, you can pick up the Draw-Tite Hitch Silencer and cover # 63080 to eliminate rattle when in...
view full answer... - Is the Swift Hitch Wide Angle and Reverse Image
- This Swift Hitch Trailer Hitch Aligner Portable Wireless Camera # 04928 features a CMOS image sensor, has a 55 degree viewing angle, and you have the choice to either select reverse image or normal for the display on the monitor.
view full answer... - Length of the Cable Between Camera and Monitor for the Hopkins Camera # HM50002
- The cable of the Hopkins Smart Hitch Backup Camera and Hitch Aligner System # HM50002 that you referenced is 20 feet long.
view full answer... - Wire Gauges for Hopkins Endurance Trailer Connector with Universal Pigtail Harness # 47210
- I reached out to my tech contact at Hopkins and the wire gauges for the Hopkins Endurance 7-Way Trailer Connector with Universal Pigtail Harness # HM47210 are as follows:
Red, Black, and Blue--14 gauge
White--12 gauge
Purple, Yellow, Green and Brown--18 gauge
So for your heat shrink butt connectors you will want # DW05743-5, # DW05744-5, and # DW05745-5.
This kit is compatible with the Hopkins Smart Hitch Backup Camera and Hitch Aligner System # HM50002 and is an easy installation. ...
view full answer... - What is the Range of the Swift Hitch Wireless Backup Camera
- I spoke with my contact about the Swift Hitch Wireless Backup Camera and Hitch Aligner # 04928 and he informed me that without any obstructions this product has a range of 300 feet. However, in most trailer/tow vehicle situations 100 feet seems to be the actual limit.
view full answer... - Dimension From Center of Hitch Balls to Center of Pin Hole on Curt Tri-Ball Adjustable Ball Mount
- The Replacement Tri-Ball for CURT Adjustable Ball Mount # C45800 has a center of pin to center of hitch ball of 4-1/8 inches. All three pin holes and the center of all 3 hitch balls are aligned with this measurement. I've attached a photo to assist.
view full answer... - Diameter of Mounting Holes on Curt Front Mounted Hitch # 33328
- The Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" # 33328 has the front 4 holes that are 21/32nds inch and the 2 rear holes are 9/16 inches. These are the measurements from the manufacturer.
view full answer... - Will the Thule Transporter Combi Hitch Mounted Enclosed Cargo Carrier Work On a 2007 Toyota Prius
- The only hitches available for the 2007 Toyota Prius are Class I hitches. The Thule Transporter Combi Hitch Mounted Enclosed Cargo Carrier, item # TH665C, is designed for Class II or larger hitches only. The carrier will not fit in a Class I hitch because the receiver hitch pin hole will not align with the hole in the shank on the carrier.
At this time we do not have any enclosed cargo carriers that are designed for the Class I hitch.
view full answer... - Distance From Hitch Pin Hole of Blue OX BX88235 to Ball Mount Opening Mounting Plate
- The distance from the center of the hitch pin hole on the Blue Ox High-Low Adapter for Tow Bars # BX88235 to the plate that holds the ball mount opening is 3 inches. I attached a picture that shows this dimension as well.
view full answer... - Pin Hole Dimensions In B&W Extend-A-Goose Gooseneck Coupler # BWTEXA4200
- The pin holes in the B&W Extend-A-Goose Gooseneck Coupler # BWTEXA4200 are 3/4" in diameter for a 3/4" Pin # BD0233060301. The 8 holes are spaced 1" on center vertically for 8" range adjustment.
view full answer... - What is the Measurement of the Bumper Bolt Holes of Curt Hitch # 13322?
- I went out to the warehouse to take a measurement and found that the bumper bolt holes on Curt hitch # 13322 measured roughly 5-1/2 inches apart center-to-center. I've added a photo for you to take a look at which has these dimensions displayed.
view full answer... - Raising Trailer with Welded On Torsion Axles
- There is a solution for you, but the lift kits you referred to such as # K71-725-02 will not work with welded on torsion axles.
The best option is for you to simply remove your torsion axles and use the Timbren Axle-Less Trailer Suspension System # TASR5200S03, which is rated for 5,200 lbs and has a 4" lift spindle. With these you would need Hub and Drum Assembly # 8-201-5UC3-EZ or Idler Hub Assembly # 8-213-5UC1-EZ.
With the Timbrens there is no alignment needed; the system does come...
view full answer... - How Far Out Does the Curt Trailer Hitch C11448 Extend From the Bumper on a 2019 Audi A5
- I wish we had the chance to install the Curt Trailer Hitch Receiver part # C11448 on a 2019 Audi A5 that way I could give you this exact measurement but sadly, that is not the case nor does the manufacturer provide this. That said, I have a really good photo for you which is attached that shows how the receiver tube aligns with the rear bumper. As you can see, the receiver tube actually sits about a few inches in from the edge of the bumper which makes for the best look and is what most...
view full answer... - How Heavy is Gen-Y Torsion 2-Ball Mount?
- The product weight of the Gen-Y Torsion 2-Ball Mount w/ Stacked Receivers # 325-GH-1225 is 87 lbs. This hitch mount is awesome due to all the extra things you can use with it. It has 5 stacked 2" hitch receivers that can accommodate almost any hitch accessory.
When you do use this though, I recommend picking up extra goodies like extra hitch pin locks # 34061650-D and anti-rattle clamps #GY88XR. Depending on what you're using this for, we also have extra tools like a weight distribution...
view full answer... - Recommended Back Up Camera for a 2011 Chevy Silverado
- For your 2011 Silverado, I recommend the Hopkins Smart Hitch Backup Camera and Hitch Aligner System item # HM50002. This system mounts to the license plate bracket on the back of your truck. It features a 3-1/2" color monitor that will give you a clear picture along with visual cues and audible alerts to ensure safety when backing up. The camera is powered by connecting to the reverse light circuit on your Silverado or by connecting directly to the OEM 7-Way.
I linked a video below of...
view full answer... - What is the Mounting Hole Spacing on Curt Trailer Hitch C13333
- I went out to the warehouse to measure the hole spacing on Curt trailer hitch # 13333 for you. The holes are spaced 7-3/4 inches apart on center. This is a custom fit hitch designed for the following vehicles:
2004 - 2014 Dodge Ram Pickup 1500 Series, without factory hitch
2003 - 2003 Dodge Ram Pickup 1500 Series, without factory hitch - built After 11/1/02
2003 - 2013 Dodge Ram Pickup 2500 and 3500 Series, without factory hitch
2010 - 2013 Ram 3500 Pickup, without factory hitch
2010 -...
view full answer... - 1-1/4 inch to 2 inch Hitch Adapter that Bike Rack with 3 inch Long Shank Fits
- I have a solution for you, but the distance from the hitch pin hole of the Curt adapter part # C45785 to the back of the hitch opening is 2.55 inches so it would not be deep enough for your bike rack. Instead we have the Brophy hitch adapter part # HTAD which has a distance of 3-1/8 inches from the pin hole to back of the hitch opening so it would be your best option.
view full answer... - Range of Adjustability that the B and W Companion Hitches Have
- To answer your first question the difference would be 8 inches from the closest and furthest away positions. In the closest position the king pin will be 1 inch ahead of the hitch socket.
Check out the picture I attached that has a chart that covers how each of the setting used for the B and W Companion heads will affect the height and distance relative to the king pin.
view full answer... - How Long is the Shank of the Curt Rebellion Cushioned Ball Mount
- I may have a solution for you, but unfortunately there is not a longer shank available for any of the cushioned hitches that we have available. The Curt Rebellion # C45949 has 7-7/8" from the center of the hitch pin hole to the center of the alignment holes. If you're ok with not using a cushioned ball mount you can use something like the Pro Series Adjustable 2-Ball Mount for 2" Hitches - 5-7/8" Drop, 4-5/8" Rise - 14K # 63071 which has 12-1/16" from the center of the hitch pin hole to...
view full answer...
Go To Results